|
PIC16F676-I/P(14-DIP) ÃÖ¼ÒÁÖ¹®¼ö·® : 20°³ |
|
|
Á¦Á¶È¸»ç : MICROCHIP |
ÆǸŰ¡°Ý : 1,400¿ø |
|
|
|
Àû¸³±Ý¾× : 0¿ø |
|
|
|
|
|
¡Ú¡Ú¡Ú¡Ú¡Ú |
½Å¼ÓÇÏ°í Á¤È®ÇÑ ¹è¼ÛÀ» ¾à¼Óµå¸³´Ï´Ù |
|
|
|
|
|
14-Pin, Flash-Based 8-Bit CMOS Microcontroller
High Performance RISC CPU: • Only 35 instructions to learn - All single-cycle instructions except branches • Operating speed: - DC - 20 MHz oscillator/clock input - DC - 200 ns instruction cycle • Interrupt capability • 8-level deep hardware stack • Direct, Indirect, and Relative Addressing modes Special Microcontroller Features: • Internal and external oscillator options - Precision Internal 4 MHz oscillator factory calibrated to ¡¾1% - External Oscillator support for crystals and resonators - 5¥ìs wake-up from SLEEP, 3.0V, typical • Power saving SLEEP mode • Wide operating voltage range - 2.0V to 5.5V • Industrial and Extended temperature range • Low power Power-on Reset (POR) • Power-up Timer (PWRT) and Oscillator Start-up Timer (OST) • Brown-out Detect (BOD) • Watchdog Timer (WDT) with independent oscillator for reliable operation • Multiplexed MCLR/Input-pin • Interrupt-on-pin change • Individual programmable weak pull-ups • Programmable code protection • High Endurance FLASH/EEPROM Cell - 100,000 write FLASH endurance - 1,000,000 write EEPROM endurance - FLASH/Data EEPROM Retention: > 40 years
Low Power Features: • Standby Current: - 1 nA @ 2.0V, typical • Operating Current: - 8.5¥ìA @ 32 kHz, 2.0V, typical - 100¥ìA @ 1 MHz, 2.0V, typical • Watchdog Timer Current - 300 nA @ 2.0V, typical • Timer1 oscillator current: - 4¥ìA @ 32 kHz, 2.0V, typical
Peripheral Features: • 12 I/O pins with individual direction control • High current sink/source for direct LED drive • Analog comparator module with: - One analog comparator - Programmable on-chip comparator voltage reference (CVREF) module - Programmable input multiplexing from device inputs - Comparator output is externally accessible • Analog-to-Digital Converter module (PIC16F676): - 10-bit resolution - Programmable 8-channel input - Voltage reference input • Timer0: 8-bit timer/counter with 8-bit programmable prescaler • Enhanced Timer1: - 16-bit timer/counter with prescaler - External Gate Input mode - Option to use OSC1 and OSC2 in LP mode as Timer1 oscillator, if INTOSC mode selected • In-Circuit Serial ProgrammingTM (ICSPTM) via two pins
µ¥ÀÌÅͽÃÆ® º¸±â
* º» Á¦Ç°Àº °æ¿ì¿¡ µû¶ó ȣȯµÇ´Â Ÿ»ç Á¦Ç°À¸·Î º¯°æµÉ ¼ö ÀÖÀ½À» ¾Ë·Á µå¸³´Ï´Ù.
ÁÖ¹®½Ã Âü°í Çϼ¼¿ä~~ |
* Á¦Ç° »ç¿ë Àü ¹Ýµå½Ã Å×½ºÆ® ÈÄ »ç¿ëÇϽñ⠹ٶø´Ï´Ù.
* ÷ºÎµÈ µ¥ÀÌÅͽÃÆ®´Â Âü°í¿ëÀ¸·Î¸¸ »ç¿ëÇϽñ⠹ٶø´Ï´Ù. |
|
|
¹øÈ£ |
|
Á¦¸ñ |
ÀÛ¼ºÀÚ |
ÀÛ¼ºÀÏ |
Á¶È¸ |
|
|
|
|